Parcel Orders over $300 Ship Free.
Euclid Eucofloor 202 50lb Bag
High strength, natural aggregate floor topping used in areas subject to moderate wear, impact, and abrasion. Floor may be returned to light wear service within 48 hours of topping placement, at 70 °F.
- Quick turnaround time
- High early strength
- Wear, abrasion and impact resistant
$56.00
SKU
19862
Euclid EucoFloor 202 – 50 lb Bag
EucoFloor 202 is a high-strength cementitious floor topping with natural aggregates for areas subject to moderate wear, impact, and abrasion. Designed for waste transfer station tipping floors and industrial slabs, it develops high early strength and can return to light wear service in about 48 hours at 70°F when placed on properly prepared substrates.
Key Features
- Resists wear, abrasion, and impact for moderate-duty service.
- High early strength enables quick turnaround.
- Return to light wear service in ~48 hours at 70°F.
- Consistent, self-consolidating mix for efficient placement.
- Compatible with EucoFloor Epoxy Primer and sand broadcast system.
- Supplied in 50 lb bags; also available in 3,000 lb super sacks.
Applications
- Waste transfer station tipping floors.
- Industrial floors exposed to moderate wear and impact.
- Service areas needing rapid strength gain and limited downtime.
Technical Specifications
| Packaging / Yield | 50 lb bag yields ~0.35 ft³; ~2.10 ft² at 2 in depth; also in 3,000 lb super sack |
| Return to Service | Light wear in ~48 hours at 70°F |
| Unit Weight (ASTM C138) | ~140.0 lb/ft³ (2,243 kg/m³) |
| Flow (ASTM C1437) | 110–130% |
| Slump (ASTM C143) | 6–9 in (15–23 cm) |
| Set Time (ASTM C403) | Final: 3–4 hours @ 70°F |
| Compressive Strength – Cubes (ASTM C109) | 1 d: ~4,500 psi; 7 d: ~6,500 psi; 28 d: ~10,000 psi |
| Compressive Strength – Cylinders (ASTM C39) | 7 d: ~6,000 psi; 28 d: ~8,000 psi |
| Rapid Chloride Permeability (ASTM C1202) | 7 d: ~3,000 coulombs; 28 d: ~750 coulombs |
| Length Change (ASTM C157, 28 d) | 50% RH: −0.050%; 100% RH: +0.050% |
| Minimum Placement Thickness | 1 in (extend with 3/8 in pea gravel if thicker than 2 in) |
| Mix Water per 50 lb Bag | 0.45–0.51 gal (1.7–1.9 L); do not vary outside range |
| Primer / Broadcast | EucoFloor Epoxy Primer at 75–100 ft²/gal; full broadcast 16/30 silica sand to refusal |
| Curing | High-solids curing compound (e.g., Super Diamond Clear VOX) ~250–300 ft²/gal; water cure under plastic/blankets if conditions are dry |
| Shelf Life | 1 year in original, unopened package |
Frequently Asked Questions
What surface prep is required?
Mechanically abrade to CSP 5–7 (heavy shotblast), clean thoroughly, and verify substrate soundness before priming.
Do I need a keyway?
Yes. Provide a perimeter keyway at least 1 in deep and ideally undercut into the base slab; feather-edging is not acceptable.
How do I prime?
Apply EucoFloor Epoxy Primer, scrub in, back-roll uniformly, then full-broadcast 16/30 silica sand to refusal and remove all loose sand after cure.
What is the minimum thickness?
1 in. For placements thicker than 2 in, extend with 3/8 in pea gravel at ~15% by weight of powder.
How is it cured?
Apply a high-solids curing compound immediately after finishing; in dry conditions, water cure under plastic/blankets after the compound is placed.
Any finishing notes?
Do not add water during troweling; if additional lubrication is needed, use Eucobar. Re-establish all joints from the base concrete through the topping.
Please complete your information below to login.